literature review on solar chimney power plant

ORIGINAL RESEARCH article

Three dimensional cfd studies of a solar chimney: effect of geometrical parameters and diurnal variations on power generated.

• 1 School of Engineering and Applied Sciences, Ahmedabad University, Ahmedabad, India
• 2 Department of Chemical Engineering, Institute of Chemical Technology, Mumbai, India

Solar power has gained particular importance in the current era due to a need of harnessing the biggest and cleanest source of energy, i. e., solar energy. One of the most innovative as well as simple technique to generate solar power is using a solar chimney. Solar chimney power plant, however, requires high investment costs and traditionally have been of very low efficiency. Mathematical and CFD models pose a good way to optimize performance of such kind of chimneys. Several factors affect the power generation from a solar chimney including geometric factors (like collector diameter, chimney height) and diurnal temperature variations. The challenge however lies in diurnal variation of temperatures and hence unstable power generation. In the present work, a pilot scale CFD model of solar chimney (of prototype of Manzanares Chimney, Spain, Haaf, 1984 ) was built and validated with experimental data and analytical models from the literature (~ <10% deviation from experimental data). Subsequently, flow patterns were studied and a parametric study was carried out for the chimney for the key parameters, namely, chimney height, and collector diameter. For the first time effect of diurnal variations on the power generated was studied. With consideration of diurnal variations, power generation during night was found to be a linear function of chimney height and collector diameter; while, during day time, the power-generated increased exponentially with variation in collector diameter and chimney height.

Introduction

Energy is one of the most important needs for the mankind. With conventional energy sources steadily depleting, economic and environmentally safe sustainable energy source needs to be found. The main sources of energy have been tabulated in Table 1 . Clean energy in terms of electricity can be generated by using renewable sources like solar, biomass, wind etc. Solar energy is one of the untapped energy sources in countries (South East Asian countries like India, European countries like Spain, African countries etc.), which have enough amount of sunlight throughout the year and enough land to receive sunlight. India has been harnessing solar power extensively in the recent years. Many devices to harness the power of solar energy, such as, photovoltaic cells, concentrated troughs etc., have been used to tap the solar energy. Implementation of these devices, however, demands large amounts of land to be occupied. This means the land would be particularly barren land. A viable option is in which energy can be utilized along with cultivation occurring on the land. Such an objective can be to certain extend can be fulfilled by harnessing the concept of a solar chimney.

Table 1 . Market share of various energy sources in India and their environmental significance.

Schematic of a typical solar chimney is shown in Figure 1 . Solar Chimney Power Plant works on the principle of natural convection based on the temperature gradient in the atmosphere and the chimney top. Also at the bottom of the chimney, solar collector absorbs solar radiations and stores the heat on natural ground. The radiation from the sun falls on the transparent cover (1). The cover is inclined and forms a cover on the natural ground (2) The air enclosed in the space (3) between (1) and (2) heats up with time. At the center of the cover lies a vertical cylindrical chimney (4) of height H and diameter D1. As temperature of the air enclosed in (3) increases, density difference between the air outside the cover (ambient air) also increases and the air enclosed in (3) and cold air gets sucked through (5). Hot air moves upward through the chimney causing an up-draft. While moving, air rotates the turbine (6) placed at the joint between the cover (2) and chimney (4). Turbine generates electricity by converting mechanical energy into electrical energy.

Figure 1 . Schematic of a typical solar Chimney.

Due to large capital involved in building the solar chimney, experimental pilot set ups have limited scope. On the other hand, advanced CFD simulations can be proved to be better tool to optimize the performance of the existing solar chimneys as well as designing improved configurations. Moreover, with cost of computation coming down and computation power going up, advanced CFD simulations can be used for detailed studies. Nonetheless, experimental validation of these simulations are essential to ensure that required physics is captured in the model. This has been our motivation for the present work.

The present paper is described as follows: Section Literature Review covers the literature overview which includes experimental as well as theoretical attempts in this field. The objective of the present work is summarized in section Objective of Present Work in order to extend limitations from the previous models. Sections Mathematical modeling and Model Equations of Theoretical Models From Literature cover governing equations used for the CFD simulations. Results are illustrated in section Results and Discussion which incorporate, model validations as well as sensitivity studies for Indian conditions. Finally, we conclude the findings in section Conclusions.

Literature Review

Researchers over the last many years have worked on analysis of solar chimney for an effective source of power generation. Significant work has been done during the past 3 decades on the effectivity of solar chimney as a power generation source. We present only a few of them here in the context and alignment of the present work. Table 2 presents some of the prominent experimental, analytical and CFD works. Research work has been done using experimental methods ( Haaf, 1984 ; Zhou et al., 2007 ; Shahreza and Imani, 2015 ), analytical models ( Padki and Sherif, 1989a , b , 1999 ; Pasumarthi and Sherif, 1998a , b ; Bernardes et al., 2003 ; Dai et al., 2003 ; Pretorius and Kroger, 2006 ; Tingzhen et al., 2006 ; Koonsrisuk and Chitsomboon, 2009 ; Panse et al., 2011 ) and Computational Fluid dynamics (CFD) analysis ( Ming et al., 2008 ; Fasel et al., 2012 ; Filkoski et al., 2013 ; Gholamalizadeh and Kim, 2014 ; Hassan et al., 2018 ).

Table 2 . Literature review of the most prominent experimental, analytical and CFD research works.

The experimental work majorly refers to the solar chimney power plant in the Manzanares desert in Spain (capacity to generate power of 50 kW), which was built as a joint effort between German ministry and a Spanish utility company. Schlaich (1995) described the concept of solar chimney power plant. ( Haaf, 1984 ) discussed the principle and construction of the power plant. Haaf (1984) also reported the design criteria and cost analysis of the Manzanares plant as well as experimental data of preliminary test results. Another important experimental work on a pilot plant was conducted by Zhou et al. (2007) . Though the pilot plant was much smaller in size (capacity to generate power of 5W), objective was to study the temperature field across the entire plant. The authors tried to find the diurnal variation of temperature across the solar collector. Their experiments could provide key data on following two parameters: 1. Maximum temperature difference in the center of the solar collector and the air outside the solar collector. 2. Criteria for obtaining a steady power generation based on identification of a span in a day when steady air flow can be obtained (without any temperature inversion). Recently, Shahreza and Imani (2015) performed experimental and numerical simulations on a small scale model of solar chimney (Diameter of chimney = 16 cm and height = 150 cm while collector diameter = 92 cm. Authors used intensifiers to intensify the heat radiated from the sun. They also used air tanks to absorb the heat radiation reflected by the intensifiers to store the heat from radiations. Authors claimed to have obtained velocities of the order of 5.12 m/s. Further, the authors performed CFD simulations for this experimental model and found good agreement with experimental results.

Padki and Sherif (1989a , b ) developed one dimensional models to find thermodynamic aspects of solar chimney power plants. They also presented a mathematical model and validated the model with experimental results of Manzanares plant. Chitsomboon (2001) presented an analytical model for frictionless one dimensional flow using conservation equations of mass and energy integrated with ideal gas relations. Author also developed a two dimensional CFD code using implicit finite volume methodology. The results of analytical model and CFD model were compared for power predictions (both qualitative and quantitative) and good agreement was observed. The analytical model of Chitsomboon (2001) determined both flow and temperature at different parts of the solar power plant. Dai et al. (2003) performed a simple energy balance to find the efficiency of the solar collector as well as the overall efficiency of the solar chimney. They used the model to predict effect of parameters, like, solar irradiance, chimney height and collector diameter on power generation. They also carried out study on the yearly variation of power for three different regions in the northwestern region of China. Koonsrisuk and Chitsomboon (2013) developed an iterative mathematical model to predict the temperatures and pressures at different points across key points in the solar chimney. Model was used by the authors to predict pressure ratio (ratio of pressure drop between inlet and outlet of air from the chimney to the pressure drop at the turbine). Model was validated with the experimental results of Manzanares prototype Spain and sensitivity studies was performed using this model for power output as a function of mass flow rate variation, pressure ratio variation, for different heights, irradiances and collector diameters. Authors found that for the system with a constant driving pressure, optimum pressure ratio was 2/3, while for a non-constant driving force, the pressure ratio is a function of plant size and solar heat flux. Hence, they claimed that their model can suggest an appropriate plant size for serving electricity to each village, which would be feasible for the local government.

Several authors have performed CFD studies for solar chimney power plants mostly for the geometrical dimensions of Manzanares power plant and validated their model with experimental data of the plant. Ming et al. (2008) performed CFD simulations to understand flow and heat transfer across the solar chimney. Authors, however, considered ground as an energy storage layer. They presented conjugate numerical simulations of the energy storage layer, collector and chimney. They used the standard k-ε model for solving turbulence equations. Main focus of the study was on importance of energy storage layer in predicting the overall prediction of temperature distribution and performance of the plant. Sangi et al. (2011) also performed CFD simulations with energy storage layer and validated with plant data of Manzaranes plant. They tried to predict temperature pressure and velocity distributions with their models. Fasel et al. (2012) carried out CFD simulations to study the effect of distance of the collector from the ground on power input. They carried out extensive simulation work to understand the effect of scale (with reference to Manzanares pilot plant) on temperature distributions between ground and temperature cover, on the collector near to the chimney and on the ground. The scales ranged from scaling down 250 times the Manzanares plant to scaling up 5 times the Manzanares plant. They found that power varied very differently in case of smaller and larger scales and hence an optimum height for optimum power generated could not be obtained. They used 2D axisymmetric simulations using unsteady Reynolds Averaged Navier-Stokes Equations (RANS) to solve the turbulence. They also compared three different turbulence models like k-ε, k-ω, and RANS and found that RANS gave the best predictions. Deviations in the prediction of power output were attributed to the fluid dynamics in between the collector and ground. Filkoski et al. (2013) performed 3D CFD simulations for a solar chimney of collector radius of 100 m and height of 100 m, with the chimney radius increasing along its height the base being 6.25 to 10.5 m. The realizable k-ε model was chosen for turbulence formulation, while discrete ordinates (DO) model was considered for accounting for thermal radiations. Authors showed predictions of velocity and temperature patterns and recommended CFD as a powerful tool for analysis of solar chimney studies. They also stressed on a need to include heat accumulation methods, like, water pipes, water bags etc., on the ground so that considerable heat can be stored in the ground to enhance the temperature gradients at night. Authors, however, did not study the effect of diurnal variations on power generated. Gholamalizadeh and Kim (2014) performed CFD simulations for the Manzaranes prototype using the realizable k-ε model for turbulence parameters and DO model for radiation heat transfer. They captured the temperature profile of the ground, thermal efficiency of the collector and power generated and validated their model with experimental results of Manzaranes prototype. They also performed detailed analysis of the green-house effect causing depth of heat penetration in the ground and increase in mean ground temperature. This increase in mean ground temperature influenced the predicted heat storage of the ground. Authors were able to provide better predictions for temperature distributions than previous researchers and could also match the Manzanares experimental data very well. Hassan et al. (2018) performed 3D CFD simulations with energy storage layer of the ground. Authors varied the chimney diverging angle from 1 to 3° and collector slope 4 to 10°. They found that the diverging angle of 1° raises the velocity from 9.1 m/s to a remarkable value of 11.6 m/s, which is good for improving the performance of the chimney.

Objective of Present Work

The review of the current literature has shown that there are only a few experimental works for raw data. Most researchers have built analytical models and tried to validate their models with the help of the available experimental data. Further, the most used experimental data is the one of Haaf (1984) to validate the models. Several analytical and CFD studies have been also undertaken, the major focus however being the effect of the geometric parameters (like the angle of the slope of collector, diverging angle of the chimney from base to top, the height of the chimney and diameter of the collector) on the performance of the chimney. Some numerical studies have been performed on the energy storage methodologies to simulate ground as an energy storage and excellent results have been obtained. There has been considerable focus on understanding the temperature distribution from the ground to the collector which is extremely important. However, once the model is robust, there seems to be a need for doing sensitivity of variation of power to cover the diurnal variations. This is a challenging task since the ground temperature, the temperature distribution across the collector, the mean velocities at the chimney inlet, the temperature difference between ground and the collector, radiation intensity all are interconnected. Further, no CFD studies have been carried out for understanding the effect of diurnal variations on the power generated.

We present a Computational Fluid Dynamics (CFD) model to study the potential of Solar Chimney as a provider of clean energy source. The CFD model is validated with the experimental data of Haaf (1984) , theoretical models of Dai et al. (2003) and Panse et al. (2011) . The present work illustrates a comprehensive approach to carry out simulations for understanding the effect of geometric parameters as well as diurnal variations on the power generated. The major contributions are as follows:

1. The study of diurnal variations provides the entire research fraternity with having an insight on further studies to be carried out on how to operate the plant during the entire day/month/year for having a sustained power supply to the power grid.

2. An effort has been made to simulate full scale geometry, with optimized grid, not compromising on the near wall mesh and turbulence model selection.

3. The CFD model has been validated with experimental data as well as with analytical models before carrying out the sensitivity study. The present work provides us with a robust model which can be used to further optimize the chimney geometry for (a) effect of energy storage on power generated diurnally, (b) monthly/yearly variations by carrying out rigorous simulations with different temperature boundary conditions, (c) understanding the physics of flow and structures during the operation of the plant at steady and unsteady state conditions.

Mathematical Modeling

In this section, we describe the methodology used for the CFD simulations including assumptions considered, governing equations solved, turbulence model selected and convergence criteria set. The grid sensitivity study is also exemplified in this section.

Assumptions

1. The temperature of heat absorption layer (earth surface) is equal to the average air temperature in the solar collector.

2. The air temperature increases along the flow direction (toward the center radially inward).

3. Air follows the ideal gas law.

4. The properties of air like density, specific heat are constant for the temperature difference considered in this work.

5. Ground is at a certain temperature T1 and ambient temperature T2.

Governing Equations, Turbulence Models, and Boundary Conditions

The governing equations used for the computational domain are given in Table 3 . Boundary conditions are as follows: The inlet was kept as pressure inlet with ambient temperature conditions. The walls of the collector were given radiation conditions using the Rosseland model. The other parameters were listed in Table 3 . The outflow boundary condition was given for the outlet of the chimney. The vertical chimney walls were kept at ambient wall temperatures. The ground was assumed to be constant temperature boundary condition.

Table 3 . Governing equations.

Grid Sensitivity

In the present work, the cylindrical chimney geometry was considered, and full scale geometry was used for grid generation. The hexahedral mesh was generated for the entire geometry with fine mesh near the walls. We managed to keep the cells to a lower value to improve the computational time to perform number of simulations. Therefore, the total computational time was reduced. Top and front view of the 3D mesh is depicted in Figures 2A,B . Grid independence was investigated by considering three different grid cases: (a) 710,000, (b) 750,000, and (c) 850,000 as shown in Figure 3 . A non-uniform hexahedral grid was used with a finer grid near the duct (where turbine is placed) where high velocity gradients were more important as compared to other zones. Approximately 60% of the nodes were located in this region, and 40% were located in the rest of the region where (according to the experimental results) the fluid was essentially quiescent and the temperature varied linearly along the length i.e., radius of the collector circle. The Y+ near the walls were kept <30 so that any effect of turbulence near wall could be captured.

Figure 2 . Mesh used for the 3D geometry (A) Top view and (B) Front view.

Figure 3 . Grid sensitivity 1. 701000 nodes, 2. 750000 nodes, and 3. 850000 nodes.

For these three cases, we compared the results of mean quantities at different positions. All the chosen grids predicted mean flow patterns effectively, but for further simulations a grid size of 750,000 cells were used. Minor differences were observed between 750,000 and 850,000. However, these were found to be within the (5% average error).

Method of Solution

The continuity, momentum, energy, and turbulence equations described in Table 3 (specify equation no.) were solved using commercial flow simulation software ANSYS FLUENT 17 1 . The SST k-ω turbulence model was used for the turbulence associated with the flow. The convergence criteria for sum of normalized residues was set to 1 × 10 −4 for continuity as well as for momentum, 1 × 10 −6 for energy equations, while 1 × 10 −5 for turbulence equations. The under-relaxation parameters were set to 0.3 for pressure, 1 each for density, energy and body forces, 0.7 for momentum equations, 0.8 for turbulence equations and 0.7 for energy equations. In this study, a segregated solver was employed for obtaining the solution of momentum equations. The momentum, energy and turbulence equations were discretized using the Second-Order Upwind Scheme (SOUS) and for pressure equation, PRESTO scheme was used. Note that SOUS scheme in the commercial software Ansys FLUENT 17 1 prevents numerical diffusion while taking care of the fact that it does not dampen the disturbances which cause the instability. Thus, this scheme ensured spatial accuracy in the simulations.

Turbulence Model Selection

The turbulence equations were solved using the SST k-ω model. The present problem under consideration has adverse pressure gradients at the node where there is an updraft of air. Due to adverse pressure gradients, the resolution at the near wall and the selection of turbulence model would be crucial for the energy dissipation predictions. Further, flow separation occurs since there is sudden expansion and recirculation is seen at the central portion. RNG k-ε has been used widely in literature for turbulence. Though RNG k-ε model is good for separated flows the near wall predictions for adverse pressure gradients needs attention in the problem at hand. We performed a study for comparing the performance of the two turbulence models for radial distribution of centerline velocities (As shown in Figure 4C to see centerline position). Figure 4A shows the variation of radial velocity for both turbulence models. A zoomed version of the near wall velocity is shown in Figure 4B . Clearly, there is slight deviation (~2–3%) between velocities predicted by RNG k-ε and SST k-ω models.

Figure 4 . Comparison of velocity for selection of turbulence model (A) Velocity profiles over the measurement line, (B) Near wall velocity profiles, and (C) Position of line selected for velocity profile (1) SST k-ω model (2) RNG k-ε model.

Model Equations of Theoretical Models from Literature

Theoretical model of dai et al. (2003).

The Equations 1 to 5 have been reproduced from Dai et al. (2003) . The efficiency of solar collector was calculated using the formulation of Dai et al. (2003) :

The mechanical power taken up by the turbine is given by

The electrical energy is given by

The total power contained in the flow is given by

Temperature difference is the one between ground and the collector.

Theoretical Model of Panse et al. (2011)

Panse et al. (2011) have considered the equation of complete energy balance to find the kinetic power of the emerging air draft. The energy balance given by them is given by:

Amount of solar energy absorbed = Change in enthalpy of air + Heat losses to the surroundings + Frictional energy loss + change in pressure energy + change in potential energy + change in kinetic energy.

Since the solar chimney is inclined, the area of the solar collector considered by Panse et al. (2011) has been mapped as per Manzanares collector area. The collector area of Panse et al. (2011) is 50,000 m 2 , whereas collector area of Manzanares is 45,216 m 2 . Further, the overall deviation of Panse et al. (2011) from that of experimental data of Manzanares was around 5% (under-prediction) ( Figure 5 ) based on power output ( P = 47.5 kW as compared to 50 kW as per experimental data).

Figure 5 . Parity plot of predicted power with experimental power. ■ CFD ▴ Theoretical model by Dai et al. (2003) ♦ Theoretical model by Panse et al. (2011) .

Results and Discussion

In this section, the results of the CFD predictions are presented. The CFD model was first validated with the experimental results of Haaf (1984) as well as was compared with findings of the theoretical models ( Dai et al., 2003 and Panse et al., 2011 ). The predictions were further illustrated in the form of Flow patterns (velocity and temperature contours) of the solar chimney. For prediction of temperature and flow patterns a lower irradiance of 200 W/m 2 was selected. The study was further extended to analyze the sensitivity of key parameters namely, height, and diameter of the chimney. For sensitivity with height and diameter, we envisage the areas in India with higher irradiance and hence, 1,000 W/m 2 was selected. The study also involved validation of model taking into account the diurnal variation of power. For diurnal variations, temperature difference between collector and ground was given as boundary condition to predict velocities at the chimney. This consideration was found to be a better way to predict diurnal variations since variation of solar irradiance over 24 h might be difficult to assume.

Model Validation

A parity plot is presented in Figure 5 , which shows the predictions of maximum and minimum power using CFD and the theoretical models ( Dai et al., 2003 and Panse et al., 2011 ) against the experimental results of Haaf (1984) . The CFD model shows around 7% deviation from the experimental results, while the theoretical model by Panse et al. (2011) shows around 5% deviation and the theoretical model of Dai et al. (2003) also shows around 7% deviation. The theoretical models as well as CFD simulations have shown comparable predictions of power. However, theoretical models have a limitation that they do not capture asymmetric effects. As a results, reliability of predictions over diverse conditions as well as different scales of operations would be limited in the case of theoretical models. CFD simulations, on the other hand, captures these dynamics in to their governing equations. Turbulence generated in the central core, where turbine is placed, become more and more critical as size of the Chimney increases and this aspect is captured effectively in the CFD models. Additionally, detailed flow as well as turbulence information is required for designing light weight turbines, essential for optimum translation of kenetic energy into electrical energy.

Flow Patterns

Domain selected for performing the CFD simulations was of Dai et al. (2003) . The domain chosen is that as specified in Table 4 . The collector diameter is twice that of Manzaranes prototype. The irradiance for the simulations was selected to be 200 W/m 2 . In Figure 6 , we show velocity contours in the domain under consideration. As observed in the figure, velocities at the far end of the chimney diameter (the entry of air) are higher. As the air moves inside horizontally toward the vertical pipe (chimney) the air velocity is lower than the entry air. It is evident that there is expansion along the collector diameter across the horizontal distance. Due to this, the pressure increases and velocities are lower as expected from Bernoulli's equation. Subsequently, as the air approaches near the central zone, velocities increase as the overall area starts converging. When air reaches the node (where the turbine is placed), there is a sudden decrease in pressure resulting in sharp increase in velocity to a maximum. The air moves up with these velocities outwards in the vertical direction. Maximum velocities of the order of 13 m/s were observed. Figures 6A–C denote the 3-dimensional effect of the chimney. Figure 6A shows the velocities at the centerline (r = 0) of the chimney and are the highest (~12 m/s), while Figures 6B, C are r = 4 m and r = −4 m, respectively. The maximum velocities are found to decrease to around 11.25 m/s and 12.5 m/s, respectively. This trend also highlights the importance of full scale 3D simulations instead of sectionized simulations or axisymmetric simulations. Mean average velocities across the plane are around 12 m/s.

Table 4 . Dimensions and parametric specifications of the Solar Chimney for Manzaranes plant and present model.

Figure 6 . Velocity contours for the solar chimney considered as per Manzaranes geometry (A) Central plane, (B) r = 4 m, and (C) r = −4 m.

Figure 7 shows temperature contours of the entire collector surface, and also depicts the vertical centerline temperatures (which includes the temperatures of the space between ground and glass surface as well as the chimney). Clearly, the temperatures increase from 296 to 310 K as we reach the chimney inlet (as can be seen in the zoomed in figure).

Figure 7 . Temperature contours for the solar chimney considered as per Manzaranes geometry.

The predicted results of both velocity and temperature were in good agreement with Ming et al. (2008) ( v = 10 m/s; ΔT = 4.5 K), which they have predicted for an irradiance of 200 W/m 2 and for a chimney whose collector is half as than that of the current chimney. The temperature difference is found to be around 10 K while mean velocities were found to be around 12 m/s. Higher temperature differences and velocities as compared to Ming et al. (2008) obtained in the present simulation is attributed to the larger collector area.

Effect of Chimney Height and Collector Diameter on Power Generated

To study the effect of height and collector diameter on the performance of the chimney in terms of power generated two cases have been considered namely (a) constant collector diameter D = 500 m with variation in height from 50 to 200 m; (b) constant height H = 200 m with variation in diameter from D = 150 m to 500 m. The irradiance for the simulations was selected to be 1,000 W/m 2 . CFD simulations were carried out to understand the effect of chimney height on the generated power. The collector area was considered constant ( D = 500 m) for these simulations. As observed, the power generated increased exponentially with chimney height ( Figure 8 ). Simulations were carried for the height up to 200 m. The predicted power for a height of 200 m was 370 KW. Further, the power generated was also dependant on the collector area. Figure 9 shows that the predicted power increases as the collector area increases in an exponential manner. The trends were similar to studies of Koonsrisuk and Chitsomboon (2009) . A maximum power up to 450 KW can be obtained with a collector diameter of 500 m. The exponential increase in power was seen for both increase in chimney height with constant collector diameter as well as increase in collector diameter with increasing chimney height. This increase could be attributed to the increase in central velocity at the node for both the cases. From Equation 4, total power was observed to be directly proportional to the velocity and since the velocity increases exponentially the power also increases exponentially. The values of power generated were much higher due to the high temperature differences considered and therefore, higher velocities at chimney inlet were predicted. It was evident from the predictions that solar irradiation during the day was much higher for such power generation to occur.

Figure 8 . Variation of predicted power with Chimney height.

Figure 9 . Variation of predicted power with Collector diameter.

Diurnal Variations of Power Generated

In countries which receive considerable sunlight throughout the year, the maximum and minimum temperatures throughout 24 h may fluctuate within 25 o C. Hence, CFD simulations were performed with temperature of 45 o C during the day and 20 o C during the night. The temperatures were chosen in close resemblance to places in India, which receive the most sun radiations across the year (Deccan Plateau). The solar irradiance was chosen as 1,000 W/m 2 during the day. Though the ambient temperature during night might be low, the stored heat of the ground would keep a surface temperature higher than the ambient temperature. Hence, suitable temperature difference has been taken accordingly. Parameters chosen for the variation are the chimney height and the total collector diameter. A trend of the predictions were similar to those described in the previous section ( Figures 10 , 11 ) especially during the day time. This trend indicates that the power generated increases exponentially with increase in chimney height and collector diameter. However, during the night, increase in the predicted power is marginal with an increase in either the collector diameter or chimney height. Interestingly, the increase in power generated for increase in height during night time is better than the increase in collector diameter.

Figure 10 . Diurnal variation of predicted power with Chimney height.

Figure 11 . Diurnal variation of predicted power with Collector diameter.

Conclusions

Solar Chimney is one of the unexplored areas in the possible option in the field of renewable solar energy utilization. CFD can prove to be a useful tool to build confidence in the design and implementation of a solar chimney. Hence, a CFD model has been developed for a case in the literature. The model was validated with the experimental data in the literature and a good agreement was found. Flow patterns in the solar chimney suggested that peak velocities up to 11 m/s can be obtained for the temperature and dimensions of the chimney under consideration. A parametric study was performed for the solar chimney to assess overall power generated for two combinations, (a) by varying the height of the chimney ( H = 50 to 200 m) at a constant collector diameter of 500 m and (b) by varying the collector diameter from 150 to 500 m for a constant height of 200 m. It was observed that for both cases the power increases exponentially as the collector diameter increases. This can be attributed to increase in central velocity at the chimney inlet where an updraft is experienced.

Another important aspect regarding prediction of power during the diurnal variations was attributed in the present paper. An important conclusion from the predicted results can be drawn that the increase in power in the night is marginal when collector diameter is increased for a fixed height. Variation of height for a fixed collector diameter gives a better trend of increase in power. The overall conclusion would be to increase the height keeping a standard collector diameter. Secondly, ways and means to find materials to store heat during the day time for the night time would help maintain the consistency in power generation over entire 24 h cycle and reduce uncertainty. As seen in literature, survey researchers have been trying to use heat storage materials and perform simulations for day time and improve the power generation. The present work actually also emphasizes that conditions during the night needs to be emphasized to see the effect of heat storage materials on the performance of power generated during night time.

Data Availability Statement

The datasets generated for this study are available on request to the corresponding author.

Author Contributions

AG: conceptualization, methodology, data curation, investigation, writing original draft, writing, review, and editing. SD: conceptualization, investigation, and review.

Conflict of Interest

The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

Acknowledgments

The authors would like to acknowledge the inputs provided by Professor A. B. Pandit during this work.

1. ^ ANSYS FLUENT 17.0 Theory Guide. ANSYS, Inc.

Bernardes, M. A., dos, S., Weinrebe, A., and Voß, G. (2003). Thermal and technical analyses of solar chimneys. Solar Energy 75, 511–524. doi: 10.1016/j.solener.2003.09.012

CrossRef Full Text | Google Scholar

Chitsomboon, T. (2001). A validated analytical model for flow in solar chimney. Int. J. Renew. Energy Eng. 3, 339–346.

Google Scholar

Dai, Y. J., Huang, H. B., and Wang, R. Z. (2003). Case study of solar chimney power plants in Northwestern regions of China. Renew. Energy 28, 1295–1304. doi: 10.1016/S0960-1481(02)00227-6

Fasel, H., Shams, E., and Gross, A. (2012). “CFD analysis for solar chimney power plants,” in 9th International conference on Heat Transfer Fluid Mechanics and Thermodynamics (Malta).

Filkoski, R. V., Stojkovski, F., and Stojkovski, V. (2013). “A CFD study of a solar chimney power plant operation,” in Proceedings of SEEP 2013 (Maribor).

Gholamalizadeh, E., and Kim, M.-H. (2014). Three-dimensional CFD analysis for simulating the greenhouse effect in solar chimney power plants using a two-band radiation model. Renew. Energy 63, 498–506. doi: 10.1016/j.renene.2013.10.011

Haaf, W. (1984). Solar chimneys, Part II: Preliminary test results from the Manzanares pilot plant. Int. J. Solar Ener. 2, 141–161. doi: 10.1080/01425918408909921

Hassan, A., Ali, M., and Waqas, A. (2018). Numerical investigation on performance of solar chimney power plant by varying collector slope and chimney diverging angle. Energy 142, 411–425. doi: 10.1016/j.energy.2017.10.047

Koonsrisuk, A., and Chitsomboon, T. (2009). Partial geometric similarity for solar chimney power plant modeling. Solar Energy 83, 1611–1618. doi: 10.1016/j.solener.2009.05.011

Koonsrisuk, A., and Chitsomboon, T. (2013). Mathematical modeling of solar chimney power plants. Energy 51, 314–322. doi: 10.1016/j.energy.2012.10.038

Ming, T. Z., Liu, W., Pan, Y., and Xu, G. L. (2008). Numerical analysis of flow and heat transfer characteristics in solar chimney power plants with energy storage layer. Energy Conver. Mange . 49, 2872–2879. doi: 10.1016/j.enconman.2008.03.004

Padki, M. M., and Sherif, S. A. (1989a). “Solar chimney for medium-to-large scale power generation,” in Proceedings of the Manila International Symposium on the Development and Management of Energy Resources , Vol. 1 (Manila), 423–437.

Padki, M. M., and Sherif, S. A. (1989b). “Solar chimney for power generation in rural areas,” in Seminar on Energy Conservation and Generation through Renewable Resources (Ranchi), 91–96.

Padki, M. M., and Sherif, S. A. (1999). On a simple analytical model for solar chimneys. Int. J. Energy Res . 23, 345–349. doi: 10.1002/(SICI)1099-114X(19990325)23:4<345::AID-ER485>3.0.CO;2-Z

Panse, S. V., Jadhav, A. S., Gudekar, A. S., and Joshi, J. B. (2011). Inclined solar chimney for power production. Energy Conver. Manage. 52, 3096–3102. doi: 10.1016/j.enconman.2011.05.001

Pasumarthi, N., and Sherif, S. A. (1998a). Experimental and theoretical performance of a demonstration solar chimney model - part I: mathematical model development. Int. J. Energy Res . 22 277–288. doi: 10.1002/(SICI)1099-114X(19980310)22:3<277::AID-ER380>3.0.CO;2-R

Pasumarthi, N., and Sherif, S. A. (1998b). Experimental and theoretical performance of a demonstration solar chimney model - part II: experimental and theoretical results and economic analysis. Int. J. Energy Res. 22 443–461. doi: 10.1002/(SICI)1099-114X(199804)22:5<443::AID-ER381>3.0.CO;2-V

Pretorius, J. P., and Kroger, D. G. (2006). Solar chimney power plant performance. J Solar Energy Engg . 128, 302–311. doi: 10.1115/1.2210491

Sangi, R., Amidpour, M., and Hosseinizadeh, B. (2011). Modeling and numerical simulation of solar chimney power plants. Solar Energy 85, 829–838. doi: 10.1016/j.solener.2011.01.011

Schlaich, J. (1995). The Solar Chimney: Electricity From the Sun . Geislingen: Axel Menges.

Shahreza, A. R., and Imani, H. (2015). Experimental and numerical investigation on an innovative solar chimney. Energy Conserv. Manage. 95, 446–452. doi: 10.1016/j.enconman.2014.10.051

Tingzhen, M., Wei, L., and Guoliang, X. (2006). Analytical and numerical investigation of the solar chimney power plant systems. Int J. Energy Res . 30, 861–873. doi: 10.1002/er.1191

Zhou, X., Yang, J., Xiao, B., and Hou, G. (2007). Experimental study of temperature field in a solar chimney power setup. Appl. Ther. Eng. 27, 2044–2050. doi: 10.1016/j.applthermaleng.2006.12.007

Nomenclature

Keywords: solar chimney, CFD, heat transfer, energy efficiency, mathematical modeling

Citation: Ganguli AA and Deshpande S (2020) Three Dimensional CFD Studies of a Solar Chimney: Effect of Geometrical Parameters and Diurnal Variations on Power Generated. Front. Chem. Eng. 2:2. doi: 10.3389/fceng.2020.00002

Received: 04 December 2019; Accepted: 10 March 2020; Published: 07 April 2020.

Reviewed by:

Copyright © 2020 Ganguli and Deshpande. This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY) . The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.

*Correspondence: Arijit A. Ganguli, ganguliarijit@gmail.com

Disclaimer: All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.

Information

• Author Services

Initiatives

You are accessing a machine-readable page. In order to be human-readable, please install an RSS reader.

All articles published by MDPI are made immediately available worldwide under an open access license. No special permission is required to reuse all or part of the article published by MDPI, including figures and tables. For articles published under an open access Creative Common CC BY license, any part of the article may be reused without permission provided that the original article is clearly cited. For more information, please refer to https://www.mdpi.com/openaccess .

Feature papers represent the most advanced research with significant potential for high impact in the field. A Feature Paper should be a substantial original Article that involves several techniques or approaches, provides an outlook for future research directions and describes possible research applications.

Feature papers are submitted upon individual invitation or recommendation by the scientific editors and must receive positive feedback from the reviewers.

Editor’s Choice articles are based on recommendations by the scientific editors of MDPI journals from around the world. Editors select a small number of articles recently published in the journal that they believe will be particularly interesting to readers, or important in the respective research area. The aim is to provide a snapshot of some of the most exciting work published in the various research areas of the journal.

Original Submission Date Received: .

• Active Journals
• Find a Journal
• Proceedings Series
• For Authors
• For Reviewers
• For Editors
• For Librarians
• For Publishers
• For Societies
• For Conference Organizers
• Open Access Policy
• Institutional Open Access Program
• Special Issues Guidelines
• Editorial Process
• Research and Publication Ethics
• Article Processing Charges
• Testimonials
• Preprints.org
• SciProfiles
• Encyclopedia

Article Menu

• Subscribe SciFeed
• Recommended Articles
• Google Scholar
• on Google Scholar
• Table of Contents

Find support for a specific problem in the support section of our website.

Please let us know what you think of our products and services.

Visit our dedicated information section to learn more about MDPI.

JSmol Viewer

A review on solar chimneys: from natural convection fundamentals to thermohydraulic best-performance proposals.

1. Introduction

1.1. fundamentals of natural convection flows, 1.2. turbulence and numerical simulations, 1.3. boussinesq approach and variable properties, 1.4. research methodology and scope, 2. basis: vertical channels, 2.1. fundamentals on natural convection in vertical channels.

Click here to enlarge figure

2.2. The Optimization Problem

3. vertical channels with extensions, 3.1. aditional spaces in vertical channels systems, 3.2. note on optimization procedures, 4. geometries approximating passive solar devices, 4.1. some topics on studied morphologies, 4.2. reference studies on passive solar systems, 4.2.1. general approach of reference studies, 4.2.2. pioneering works on solar passive systems, 5. overview of relevant literature, 6. solar chimneys: topics, 6.1. prevailing buoyancy, 6.2. taking into account radiative effects, 6.3. wind-driving effects, 6.4. fundamentals of wind numerical simulation, 7. solar chimneys: shapes and designs, 7.1. shapes and designs. background, 7.2. tilt-related studies, 7.3. width-related studies, 7.4. inlet/outlet-related studies, 8. solar chimneys: plates, fins, and flow disturbers, 8.1. intermediate plates, 8.3. obstacles and vortex generators, 9. short note on the influence of climatic conditions, 10. summary, data availability statement, conflicts of interest.

• Bejan, A. Convection Heat Transfer ; Wiley: New York, NY, USA, 1984. [ Google Scholar ]
• Incropera, F.P.; De Witt, D.P. Introduction to Heat Transfer ; Wiley: New York, NY, USA, 1990. [ Google Scholar ]
• Bejan, A. Heat Transfer ; Wiley: New York, NY, USA, 1993. [ Google Scholar ]
• Turner, J.S. Buoyancy Effects in Fluids ; Cambridge University Press: Cambridge, UK, 1973. [ Google Scholar ]
• Yuan, X.; Moser, A.; Suter, P. Wall functions for numerical simulation of turbulent natural convection along vertical plates. Int. J. Heat Mass Transf. 1993 , 36 , 4477–4485. [ Google Scholar ] [ CrossRef ]
• Versteegh, T.A.; Nieuwstadt, F.T. A direct numerical simulation of natural convection between two infinite vertical differentially heated walls scaling laws and wall functions. Int. J. Heat Mass Transf. 1999 , 42 , 3673–3693. [ Google Scholar ] [ CrossRef ]
• Henkes, R.A.W.M.; Hoogendorn, C.J. Comparison exercise for computations of turbulent natural convection in enclosures. Numer. Heat Transf. 1995 , 28 , 59–78. [ Google Scholar ] [ CrossRef ]
• Fedorov, A.G.; Viskanta, R. Turbulent natural convection heat transfer in an asymmetrically heated, vertical parallel-plate channel. Int. J. Heat Mass Transf. 1997 , 40 , 3849–3860. [ Google Scholar ] [ CrossRef ]
• Wilcox, D.C. Turbulence Modeling for CFD , 3rd ed.; DCW Industries: La Cañada, CA, USA, 2006. [ Google Scholar ]
• Peng, S.; Davison, L. Computation of turbulent buoyant flows in enclosures with low-Reynolds number k – ω models. Int. J. Heat Fluid Flow 1999 , 20 , 172–184. [ Google Scholar ] [ CrossRef ]
• Xu, W.; Chen, Q.; Nieuwstadt, F.T.M. A new turbulence model for near wall natural convection. Int. J. Heat Mass Transf. 1998 , 41 , 3161–3176. [ Google Scholar ] [ CrossRef ]
• Ciofalo, M. Large-eddy simulations of turbulent flow with heat transfer in simple and complex geometries using Harwell-FLOW3D. Appl. Math. Model. 1996 , 20 , 262–271. [ Google Scholar ] [ CrossRef ]
• Salinas-Vázquez, M.; Vicente, W.; Martínez, E.; Barrios, E. Large eddy simulation of a confined square cavity with natural convection based on compressible flow equations. Int. J. Heat Fluid Flow 2011 , 32 , 876–878. [ Google Scholar ] [ CrossRef ]
• Zhou, Y.; Zhang, R.; Staroselsky, I.; Chen, H. Numerical simulation of laminar and turbulent buoyancy-driven flows using a lattice-Boltzmann based-algorithm. Int. J. Heat Mass Transf. 2004 , 47 , 4869–4879. [ Google Scholar ] [ CrossRef ]
• Nokhosteen, A.; Sobhansarbandi, S. Utilizing lattice Boltzmann method for heat transfer analysis in solar thermal systems. Sustain. Energy Technol. Assess. 2021 , 46 , 101264. [ Google Scholar ] [ CrossRef ]
• Gray, D.D.; Giorgini, A. The validity of the Boussinesq approximation for liquids and gases. Int. J. Heat Mass Transf. 1976 , 19 , 545–551. [ Google Scholar ] [ CrossRef ]
• Zhong, Z.Y.; Yang, K.T.; Lloyd, J.R. Variable property effects in laminar natural convection in a square enclosure. ASME J. Heat Transf. 1985 , 107 , 133–138. [ Google Scholar ] [ CrossRef ]
• Emery, A.F.; Lee, J.W. The effects of property variations on natural convection in a square enclosure. ASME J. Heat Transf. 1999 , 121 , 57–62. [ Google Scholar ] [ CrossRef ]
• Chenoweth, D.R.; Paolucci, S. Natural convection in an enclosed vertical air layer with large horizontal temperature differences. J. Fluid Mech. 1986 , 169 , 173–210. [ Google Scholar ] [ CrossRef ]
• Guo, Z.Y.; Wu, X.B. Thermal drag and critical heat flux for natural convection of air in vertical parallel plates. ASME J. Heat Transf. 1993 , 115 , 124–129. [ Google Scholar ] [ CrossRef ]
• Guo, Z.Y.; Song, Y.Z.; Li, Z.X. Laser speckle photography in heat transfer studies. Exp. Thermal Fluid Sci. 1995 , 10 , 1–16. [ Google Scholar ] [ CrossRef ]
• Elenbaas, W. Heat dissipation of parallel plates by free convection. Physica 1942 , 9 , 1–8. [ Google Scholar ] [ CrossRef ]
• Aihara, T. Effects of inlet boundary conditions on numerical solutions of free convection between vertical parallel plates. Rep. Inst. High Speed Mech. 1973 , 28 , 258. [ Google Scholar ]
• Kettleborough, C.F. Transient laminar free convection between heated vertical plates including entrance effects. Int. J. Heat Mass Transf. 1972 , 15 , 883–896. [ Google Scholar ] [ CrossRef ]
• Nakamura, H.; Yutaka, A.; Naitou, T. Heat transfer by free convection between two parallel flat plates. Numer. Heat Transf. 1982 , 5 , 95–106. [ Google Scholar ] [ CrossRef ]
• Desrayaud, G.; Chénier, E.; Joulin, A.; Bastide, A.; Brangeon, B.; Caltagirone, J.P.; Cherif, Y.; Eymard, R.; Garnier, C.; Giroux-Julien, S.; et al. Benchmark solutions for natural convection flows in vertical channels submitted to different open boundary conditions. Int. J. Therm. Sci. 2013 , 72 , 18–33. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Wong, S.C.; Chu, S.H. Revisit on natural convection from vertical isothermal plate arrays-effects of extra plume buoyancy. Int. J. Therm. Sci. 2017 , 120 , 263–272. [ Google Scholar ] [ CrossRef ]
• Bodoia, J.R.; Osterle, J.F. The development of free convection between heated vertical plates. ASME J. Heat Transf. 1962 , 84 , 40–44. [ Google Scholar ] [ CrossRef ]
• Bar-Cohen, A.; Rohsenow, W.M. Thermally optimum spacing of vertical, natural convection cooled, parallel plates. ASME J. Heat Transf. 1984 , 106 , 116–123. [ Google Scholar ] [ CrossRef ]
• Anand, N.K.; Kim, S.H.; Fletcher, L.S. The effect of plate spacing on free convection between heated parallel plates. ASME J. Heat Transf. 1992 , 114 , 515–518. [ Google Scholar ] [ CrossRef ]
• Zamora, B.; Hernández, J. Influence of upstream conduction on the thermally optimum spacing of isothermal, natural convection-cooled vertical plate arrays. Int. Commun. Heat Mass Transf. 2001 , 28 , 201–210. [ Google Scholar ] [ CrossRef ]
• Zamora, B. Thermally optimum spacing between inner plates in natural convection flows in cavities by numerical investigation. Processes 2020 , 8 , 554. [ Google Scholar ] [ CrossRef ]
• Haaland, S.E.; Sparrow, E.M. Solutions for the channel plume and the parallel-walled chimney. Num. Heat Transf. 1983 , 6 , 155–172. [ Google Scholar ] [ CrossRef ]
• Straatman, A.G.; Tarasuk, J.D.; Floryan, J.M. Heat transfer enhancement from a vertical, isothermal channel generated by the chimney effect. ASME J. Heat Transf. 1993 , 115 , 395–402. [ Google Scholar ] [ CrossRef ]
• Morrone, B.; Campo, A.; Manca, O. Optimum plate separation in vertical parallel-plate channels for natural convective flows: Incorporation of large spaces at the channel extremes. Int. J. Heat Mass Transf. 1997 , 40 , 993–1000. [ Google Scholar ] [ CrossRef ]
• Ledezma, G.A.; Bejan, A. Optimal geometric arrangement of staggered vertical plates in natural convection. ASME J. Heat Transf. 1997 , 119 , 700–708. [ Google Scholar ] [ CrossRef ]
• Viswatmula, P.; Ruhul Amin, M. Effects of multiple obstructions on natural convection heat transfer in vertical channels. Int. J. Heat Mass Transf. 1995 , 38 , 2039–2046. [ Google Scholar ] [ CrossRef ]
• Zhang, X.; Liu, D. Optimum geometric arrangement of vertical rectangular fin arrays. Energy Convers Manag. 2010 , 51 , 2449–2456. [ Google Scholar ] [ CrossRef ]
• Ben Maad, R.; Belghith, A. The use of grid-generated turbulence to improve heat transfer in passive solar systems. Renew. Energy 1992 , 2 , 333–336. [ Google Scholar ] [ CrossRef ]
• Bejan, A. Shape and Structure, from Engineering to Nature ; Cambridge University Press: Cambridge, UK, 2000. [ Google Scholar ]
• Bejan, A.; Lorente, S. The constructal law and the thermodynamics of flow system with configuration. Int. J. Heat Mass Transf. 2004 , 47 , 3203–3214. [ Google Scholar ] [ CrossRef ]
• Da Silva, A.L.; Lorenzini, G.; Bejan, A. Distribution of heat sources in vertical channels with natural convection. Int. J. Heat Mass Transf. 2005 , 48 , 1462–1469. [ Google Scholar ] [ CrossRef ]
• Da Silva, A.K.; Gosselin, L. Optimal geometry of L and C-shaped channels for maximum heat transfer rate in natural convection. Int. J. Heat Mass Transf. 2005 , 48 , 609–620. [ Google Scholar ] [ CrossRef ]
• Zamora, B.; Kaiser, A.S. Optimum wall-to-wall spacing in solar chimney shaped channels in natural convection by numerical investigation. Appl. Therm. Eng. 2009 , 29 , 762–769. [ Google Scholar ] [ CrossRef ]
• Zamora, B.; Kaiser, A.S. Thermal and dynamic optimization of the convective flow in Trombe Wall shaped channels by numerical investigation. Heat Mass Transf. 2009 , 45 , 1393–1407. [ Google Scholar ] [ CrossRef ]
• Aounallah, M.; Belkadi, M.; Adjlout, L.; Imine, O. Numerical shape optimization of a confined cavity in natural convection regime. Comput. Fluids 2013 , 75 , 11–21. [ Google Scholar ] [ CrossRef ]
• Biserni, C.; Rocha, L.A.O.; Stanescu, G.; Lorenzini, E. Constructal H-shaped cavities according to Bejan’s theory. Int. J. Heat Mass Transf. 2007 , 50 , 2132–2138. [ Google Scholar ] [ CrossRef ]
• Lorenzini, G.; Biserni, C.; García, F.L.; Rocha, L.A.O. Geometric optimization of a convective T-shaped cavity on the basis of constructal theory. Int. J. Heat Mass Transf. 2012 , 55 , 6951–6958. [ Google Scholar ] [ CrossRef ]
• Lorenzini, G.; Rocha, L.A.O. Geometric optimization of T-Y-shaped cavity according to Constructal design. Int. J. Heat Mass Transf. 2009 , 52 , 4683–4688. [ Google Scholar ] [ CrossRef ]
• Linden, P.F. The fluid mechanics of natural ventilation. Ann. Rev. Fluid Mech. 1999 , 31 , 201–238. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Borgers, T.R.; Akbari, H. Free convective turbulent flow within the Trombe wall channel. Sol. Energy 1984 , 33 , 253–264. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Smolec, W.; Thomas, A. Problems encountered in heat transfer studies of a Trombe wall. Energy Convers Manag. 1994 , 35 , 483–491. [ Google Scholar ] [ CrossRef ]
• Smolec, W.; Thomas, A. Theoretical and experimental investigations of heat transfer in a Trombe wall. Energy Convers Manag. 1994 , 34 , 385–400. [ Google Scholar ] [ CrossRef ]
• Jubran, B.A.; Hamdan, M.A.; Manfalouti, W. Modelling free convection in a Trombe wall. Renew. Energy 1991 , 1 , 351–360. [ Google Scholar ] [ CrossRef ]
• Gan, G.; Riffat, S.B. A numerical study of solar chimney for natural ventilation of buildings with heat recovery. Appl. Therm. Eng. 1998 , 18 , 117–187. [ Google Scholar ] [ CrossRef ]
• Gan, G. A parametric study of Trombe walls for passive cooling of buildings. Energy Build. 1998 , 27 , 37–43. [ Google Scholar ] [ CrossRef ]
• Awbi, H.B. Design considerations for naturally ventilated buildings. Renew. Energy 1994 , 5 , 1081–1090. [ Google Scholar ] [ CrossRef ]
• Ong, K.S. A mathematical model of a solar chimney. Renew. Energy 2003 , 28 , 1047–1060. [ Google Scholar ] [ CrossRef ]
• Ong, K.S.; Chow, C.C. Performance of a solar chimney. Solar Energy 2003 , 17 , 1–17. [ Google Scholar ] [ CrossRef ]
• Bouchair, A. Solar chimney for promoting cooling ventilation in southern Algeria. Build. Serv. Eng. Res. Technol. 1994 , 15 , 81–93. [ Google Scholar ] [ CrossRef ]
• Warringon, R.O.; Ameel, T.A. Experimental studies of natural convection in partitioned enclosures with a Trombe wall geometry. ASME J. Solar Energy Eng. 1995 , 117 , 16–21. [ Google Scholar ] [ CrossRef ]
• Afonso, A.; Oliveira, A. Solar chimneys: Simulation and experiment. Energy Build. 2000 , 32 , 71–79. [ Google Scholar ] [ CrossRef ]
• Onbasioglu, H.; Egrican, A.N. Experimental approach to the thermal response of passive systems. Energy Convers. Manag. 2002 , 43 , 2053–2065. [ Google Scholar ] [ CrossRef ]
• Stevanović, S. Optimization of passive solar design strategies: A review. Renew. Sustain. Energy Rev. 2013 , 25 , 177–196. [ Google Scholar ] [ CrossRef ]
• Zhang, T.; Tan, Y.; Yang, H.; Zhang, X. The application of air layers in building envelopes: A review. Appl. Energy 2016 , 165 , 707–734. [ Google Scholar ] [ CrossRef ]
• Omrany, H.; Ghaffarianhoseini, A.; Ghaffarianhoseini, A.; Raahemifar, K.; Tookey, J. Application of passive solar systems for improving the energy efficiency in buildings: A comprehensive review. Renew. Sustain. Energy Rev. 2016 , 62 , 1252–1269. [ Google Scholar ] [ CrossRef ]
• Zhai, X.Q.; Song, Z.P.; Wang, R.Z. A review for the applications of solar chimneys in buildings. Renew. Sustain. Energy Rev. 2011 , 15 , 3757–3767. [ Google Scholar ] [ CrossRef ]
• Shi, L.; Zhang, G.; Yang, W.; Huang, D.; Cheng, X.; Setunge, S. Determining the influencing factors on the performance of solar chimney in building. Renew. Sustain. Energy Rev. 2018 , 88 , 223–238. [ Google Scholar ] [ CrossRef ]
• Zhang, H.; Tao, Y.; Shi, L. Solar chimney applications in buildings. Encyclopedia 2021 , 1 , 409–422. [ Google Scholar ] [ CrossRef ]
• Ding, W.; Hasemi, Y.; Yamada, T. Natural ventilation performance of a double-skin façade with a solar chimney. Energy Build. 2005 , 37 , 411–418. [ Google Scholar ] [ CrossRef ]
• Mathur, J.; Bansal, N.K.; Mathur, S.; Jain, M.; Anupma. Experimental investigation on solar chimney for room ventilation. Sol. Energy 2006 , 80 , 927–935. [ Google Scholar ] [ CrossRef ]
• Mathur, J.; Mathur, S.; Anupma. Summer-performance of inclined roof solar chimney for natural convection. Energy Build. 2006 , 38 , 1156–1163. [ Google Scholar ] [ CrossRef ]
• Burek, S.A.M.; Habeb, A. Air flow and thermal efficiency characteristics in solar chimney and Trombe walls. Energy Build. 2007 , 39 , 128–135. [ Google Scholar ] [ CrossRef ]
• Arce, J.; Jiménez, M.J.; Guzmán, J.D.; Heras, M.R.; Álvarez, G.; Xamán, J. Experimental study for natural ventilation on a solar chimney. Renew. Energy 2009 , 34 , 2928–2934. [ Google Scholar ] [ CrossRef ]
• Bacharoudis, E.; Vrachopoulos, M.G.; Koukou, M.K.; Margaris, D.; Filios, A.E.; Mavrommatis, S.A. Study of the natural convection phenomena inside a solar chimney with one wall adiabatic and one wall under heat flux. Appl. Therm. Eng. 2007 , 27 , 2266–2275. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Harris, D.J.; Helwing, N. Solar chimney and building ventilation. Appl. Energy 2007 , 84 , 135–146. [ Google Scholar ] [ CrossRef ]
• Bassiouny, R.; Koura, N.S.A. An analytical and numerical study of solar chimney use for room natural ventilation. Energy Build. 2008 , 40 , 865–873. [ Google Scholar ] [ CrossRef ]
• Zhang, H.; Tao, Y.; Nguyen, K.; Han, F.; Li, J.; Shi, L. A wall solar chimney to ventilate multi-zone buildings. Sustain. Energy Technol. Assess. 2021 , 47 , 101381. [ Google Scholar ] [ CrossRef ]
• Shi, L.; Zhang, G. An empirical model to predict the performance of typical solar chimneys considering both room and cavity configurations. Build. Environ. 2016 , 103 , 250–261. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Jiménez-Xamán, C.; Xamán, J.; Gijón-Rivera, M.; Zavala-Guillén, I.; Noh-Pat, F.; Simá, E. Assessing the thermal performance of a rooftop solar chimney attached to a single room. J. Build. Eng. 2020 , 31 , 101380. [ Google Scholar ] [ CrossRef ]
• Vázquez-Ruíz, A.; Navarro, J.M.A.; Hinojosa, J.F.; Xamán, J.P. Effect of the solar chimney position on heat transfer in a room. Int. J. Mech. Sci. 2021 , 209 , 106700. [ Google Scholar ] [ CrossRef ]
• Lee, K.H.; Strand, R.K. Enhancement of natural ventilation in buildings using a thermal chimney. Energy Build. 2009 , 41 , 615–621. [ Google Scholar ] [ CrossRef ]
• Singh, A.P.; Akshayveer; Kumar, A.; Singh, O.P. Designs for high flow natural convection solar air heaters. Sol. Energy 2019 , 193 , 724–737. [ Google Scholar ] [ CrossRef ]
• Singh, A.P.; Akshayveer; Kumar, A.; Singh, O.P. Natural convection solar air heater: Bell-mounted integrated converging channel for high flow applications. Build. Environ. 2021 , 187 , 107367. [ Google Scholar ] [ CrossRef ]
• Zhang, L.; Dong, J.; Sun, S.; Chen, Z. Numerical simulation and sensitivity analysis on an improved Trombe wall. Sustain. Energy Technol. Assess. 2021 , 43 , 100941. [ Google Scholar ] [ CrossRef ]
• Liu, H.; Li, P.; Yu, B.; Zhang, M.; Tan, Q.; Wang, Y.; Zhang, Y. Contrastive analysis on the ventilation performance of a combined solar chimney. Appl. Sci. 2022 , 12 , 156. [ Google Scholar ] [ CrossRef ]
• Nguyen, A.Q.; Nguyen, V.T.; Tran, L.T.; Wells, J.C. CFD analysis of different ventilation strategies for a room with a heated wall. Buildings 2022 , 12 , 1300. [ Google Scholar ] [ CrossRef ]
• Nouanégué, H.F.; Bilgen, E. Heat transfer by convection, conduction and radiation in solar chimney systems for ventilation of dwellings. Int. J. Heat Fluid Flow 2009 , 30 , 150–157. [ Google Scholar ] [ CrossRef ]
• Montiel, M.; Hinojosa, J.; Estrada, C.A. Numerical study of heat transfer by natural convection and surface thermal radiation in an open cavity receiver. Sol. Energy 2012 , 86 , 1118–1128. [ Google Scholar ] [ CrossRef ]
• Zamora, B.; Kaiser, A.S. Radiative and variable thermophysical properties effects on turbulent convective flows in cavities with thermal passive configuration. Int. J. Heat Mass Transf. 2017 , 109 , 981–996. [ Google Scholar ] [ CrossRef ]
• Bansal, N.K.; Mathur, R.; Bhandari, M.S. A study of solar chimney assisted wind tower system for natural ventilation in buildings. Build. Environ. 1994 , 29 , 495–500. [ Google Scholar ] [ CrossRef ]
• Nouanégué, H.F.; Alandji, L.R.; Bilgen, E. Numerical study of solar-wind tower systems for ventilation of dwellings. Renew. Energy 2008 , 33 , 434–443. [ Google Scholar ] [ CrossRef ]
• Zamora, B.; Kaiser, A.S. Numerical study on mixed buoyancy-wind driving induced flow in a solar chimney for building ventilation. Renew. Energy 2010 , 35 , 2080–2088. [ Google Scholar ] [ CrossRef ]
• Neves, L.O.; Da Silva, F.M. Simulation and measurements of wind interference on a solar chimney performance. J. Wind Eng. Ind. Aerodyn. 2018 , 179 , 135–145. [ Google Scholar ] [ CrossRef ]
• Shi, L. Impacts of wind on solar chimney performance in a building. Energy 2019 , 185 , 55–67. [ Google Scholar ] [ CrossRef ]
• Wang, Q.; Zhang, G.; Li, W.; Shi, L. External wind on the optimum parameters of a wall solar chimney in building. Sustain. Energy Technol. Assess. 2020 , 42 , 100842. [ Google Scholar ] [ CrossRef ]
• Moosavi, L.; Zandi, M.; Bidi, M.; Behroozizade, E.; Kazemi, I. New design for solar chimney with integrated windcatcher for space cooling and ventilation. Build. Environ. 2020 , 181 , 106785. [ Google Scholar ] [ CrossRef ]
• Jomehzadeh, F.; Hussen, H.M.; Calaudit, J.K.; Nejat, P.; Ferwati, M.S. Natural ventilation by windcatcher (Bagdir): A review on the impacts of geometry, microclimate and macroclimate. Energy Build. 2020 , 226 , 110396. [ Google Scholar ] [ CrossRef ]
• Evola, G.; Popov, V. Computational analysis of wind driven natural ventilation in buildings. Energy Build. 2006 , 38 , 491–501. [ Google Scholar ] [ CrossRef ]
• Pakari, A.; Ghani, S. Aiflow assessment in a naturally ventilated greenhouse equipped with wind towers: Numerical simulation and wind tunnel experiments. Energy Build. 2019 , 199 , 1–11. [ Google Scholar ] [ CrossRef ]
• Ramponi, R.; Blocken, B. CFD simulation of cross-ventilation for a generic isolated building: Impact of computational parameters. Build. Environ. 2012 , 53 , 34–48. [ Google Scholar ] [ CrossRef ]
• Park, J.; Sun, X.; Choi, J.-I.; Rhee, G.H. Effect of wind and buoyancy interaction on single-sided ventilation in a building. J. Wind Eng. Ind. Aerodyn. 2017 , 171 , 380–389. [ Google Scholar ] [ CrossRef ]
• Grimmond, C.S.B.; Oke, T.R. Aerodynamic properties of urban areas derived from analysis of surface form. J. Appl. Meteorol. 1999 , 38 , 1262–1292. [ Google Scholar ] [ CrossRef ]
• Blocken, B.; Van der Hout, A.; Dekker, J.; Weiler, O. CFD simulation of wind flow over natural complex terrain: Case study with validation by field measurements for Ria de Ferrol, Galicia, Spain. J. Wind Eng. Ind. Aerodyn. 2015 , 147 , 43–57. [ Google Scholar ] [ CrossRef ]
• Richards, P.J.; Hoxey, R.P. Appropriate boundary conditions for computational wind engineering models using the k–ω turbulence model. J. Wind Eng. Ind. Aerodyn. 1993 , 46–47 , 145–153. [ Google Scholar ] [ CrossRef ]
• Blocken, B.; Stathopoulos, T.; Carmeliet, J. CFD simulations of the atmospheric boundary layer: Wall function problems. Atmos. Environ. 2007 , 41 , 238–252. [ Google Scholar ] [ CrossRef ]
• Richards, P.J.; Norris, S.E. Appropriate boundary conditions for computational wind engineering models revised. J. Wind Eng. Ind. Aerodyn. 2011 , 99 , 257–266. [ Google Scholar ] [ CrossRef ]
• Van Hoof, T.; Blocken, B.; Tominaga, Y. On the accuracy of CFD simulations of cross-ventilation flows for a generic isolated building: Comparison of RANS, LES and experiments. Build. Environ. 2017 , 114 , 148–165. [ Google Scholar ] [ CrossRef ]
• Palyvos, J.A. A survey of wind convection coefficient correlations for building envelope energy systems’ modeling. Appl. Therm. Eng. 2008 , 28 , 801–808. [ Google Scholar ] [ CrossRef ]
• Zhang, H.; Yang, D.; Tam, V.W.Y.; Tao, Y.; Zhang, G.; Setunge, S.; Shi, L. A critical review of combined natural ventilation techniques in sustainable buildings. Renew. Sustain. Energy Rev. 2021 , 141 , 110795. [ Google Scholar ] [ CrossRef ]
• Shaeri, J.; Mahdavinejad, M. A new design to create natural ventilation in buildings: Wind chimney. J. Build. Eng. 2022 , 59 , 105041. [ Google Scholar ] [ CrossRef ]
• Sakonidou, E.P.; Karapantsios, T.D.; Balouktis, A.I.; Chassapis, D. Modeling of the optimum tilt of a solar chimney for maximum air flow. Sol. Energy 2008 , 82 , 80–94. [ Google Scholar ] [ CrossRef ]
• Prasad, M.; Chandra, K.S. Optimum tilt of solar collector for maximum natural flow. Energy Convers. Manag. 1990 , 30 , 369–379. [ Google Scholar ] [ CrossRef ]
• Bassiouny, R.; Korah, N.S.A. Effect of solar chimney inclination angle on space flow pattern and ventilation rate. Energy Build. 2009 , 41 , 190–196. [ Google Scholar ] [ CrossRef ]
• Khanal, R.; Lei, C. Flow reversal effects on buoyancy induced air flow in a solar chimney. Sol. Energy 2012 , 86 , 2783–2794. [ Google Scholar ] [ CrossRef ]
• Khanal, R.; Lei, C. An experimental investigation of an inclined passive wall solar chimney for natural ventilation. Sol. Energy 2014 , 107 , 461–474. [ Google Scholar ] [ CrossRef ]
• Ren, X.H.; Wang, L.; Liu, R.Z.; Wang, L.; Zhao, F.Y. Thermal stack airflows inside the solar chimney with discrete heat sources: Reversal flow regime defined by chimney inclination and thermal Rayleigh number. Renew. Energy 2021 , 163 , 342–356. [ Google Scholar ] [ CrossRef ]
• Kong, J.; Niu, J.; Lei, C. A CFD based approach for determining the optimum inclination angle of a roof-top solar chimney for building ventilation. Sol. Energy 2020 , 198 , 555–569. [ Google Scholar ] [ CrossRef ]
• Zavala-Guillén, I.; Xamán, J.; Hernández-Pérez, I.; Hernández-López, I.; Gijón-Rivera, M.; Chávez, Y. Numerical study of the optimum width of 2a diurnal double air-channel solar chimney. Energy 2018 , 47 , 403–417. [ Google Scholar ] [ CrossRef ]
• Zamora, B. Morphological comparative assessment of a rooftop solar chimney through numerical modeling. Int. J. Mech Sci. 2022 , 227 , 107441. [ Google Scholar ] [ CrossRef ]
• Al-Kayiem, H.H.; Sreejaya, K.V.; Ul-Haq Gilani, S.I. Mathematical analysis of the influence of the chimney height and collector area on the performance of a roof top solar chimney. Energy Build. 2014 , 68 , 305–311. [ Google Scholar ] [ CrossRef ]
• Al-Kayiem, H.H.; Sreejaya, K.V.; Chikere, A.O. Experimental and numerical analysis of the influence of inlet configuration on the performance of a roof top solar chimney. Energy Build. 2018 , 159 , 89–98. [ Google Scholar ] [ CrossRef ]
• He, G. A general model for predicting the airflow rates of a vertically installed solar chimney with connecting ducts. Energy Build. 2020 , 229 , 110481. [ Google Scholar ] [ CrossRef ]
• He, G.; Zhang, J.; Hong, S. A new analytical model for airflow in solar chimneys based on thermal boundary layers. Sol. Energy 2016 , 136 , 614–621. [ Google Scholar ] [ CrossRef ]
• Nguyen, Y.Q.; Wells, J.C. Effects of wall proximity on the airflow in a vertical solar chimney for natural ventilation of dwellings. J. Build. Phys. 2020 , 44 , 225–250. [ Google Scholar ] [ CrossRef ]
• Nguyen, Y.Q.; Nguyen, V.T. Characterizing the induced flow through the cavity of a wall solar chimney under the effects of the opening heights. J. Build. Phys. 2022 . [ Google Scholar ] [ CrossRef ]
• Fang, Z.; Wang, W.; Chen, Y.; Song, J. Structural and heat transfer model analysis of wall-mounted solar chimney inlets and outlets in single-story buildings. Buildings 2022 , 12 , 1790. [ Google Scholar ] [ CrossRef ]
• Gao, N.; Yan, Y.; Sun, R.; Lei, Y. Natural ventilation enhancement of a roof solar chimney with wind-induced channel. Energies 2022 , 15 , 6492. [ Google Scholar ] [ CrossRef ]
• Ren, X.H.; Liu, R.Z.; Wang, Y.H.; Wang, L.; Zhao, F.Y. Thermal driven natural convective flows inside the solar chimney flush-mounted with discrete heating sources: Reversal and cooperative flow dynamics. Renew. Energy 2019 , 138 , 354–367. [ Google Scholar ] [ CrossRef ]
• Tkachenko, O.A.; Giroux-Julien, S.; Timchenko, V.; Ménézo, C.; Yeoh, G.H.; Reizes, J.A.; Sanvicente, E.; Fossa, M. Numerical and experimental investigation of unsteady natural convection in a non-uniformly heated vertical open-ended channel. Int. J. Therm. Sci. 2016 , 99 , 9–25. [ Google Scholar ] [ CrossRef ]
• Zavala-Guillén, I.; Xamán, J.; Álvarez, G.; Arce, J.; Hernández-Pérez, I.; Gijón-Rivera, M. Computational fluid dynamics for modeling the turbulent natural convection in a double air-channel solar chimney system. Int. J. Mod. Phys. 2016 , 27 , 1650095. [ Google Scholar ] [ CrossRef ]
• Zavala-Guillén, I.; Xamán, J.; Hernández-Pérez, I.; Hernández-López, I.; Jiménez-Xamán, C.; Moreno-Bernal, P.; Sauceda, D. Ventilation potential of an absorber-partitioned air channel solar chimney for diurnal use under Mexican climate conditions. Appl. Therm. Eng. 2019 , 149 , 807–821. [ Google Scholar ] [ CrossRef ]
• He, G.; Lv, D. Distributed heat absorption in a solar chimney to enhance ventilation. Sol. Energy 2022 , 238 , 315–326. [ Google Scholar ] [ CrossRef ]
• Lei, Y.; Zhang, Y.; Wang, F.; Wang, X. Enhancement of natural ventilation of a novel roof solar chimney with perforated absorber plate for building energy conservation. Appl. Therm. Eng. 2016 , 107 , 653–661. [ Google Scholar ] [ CrossRef ]
• Chen, Z.D.; Bandopadhayay, P.; Halldorsson, J.; Byrjalsen, C.; Heiselberg, P.; Li, Y. An experimental investigation of a solar chimney model with uniform wall heat flux. Build. Environ. 2003 , 38 , 893–906. [ Google Scholar ] [ CrossRef ]
• Wu, S.Y.; Yan, R.R.; Xiao, L. Numerically predicting the effect of fin on solar Trombe wall performance. Sustain. Energy Technol. Assess. 2022 , 52 , 102012. [ Google Scholar ] [ CrossRef ]
• Hosseini, S.S.; Ramiar, A.; Ranjbar, A. Numerical investigation of rectangular fin geometry effect on solar chimney. Energy Build. 2017 , 155 , 296–307. [ Google Scholar ] [ CrossRef ]
• Hosseini, S.S.; Ramiar, A.; Ranjbar, A. Numerical investigation of natural convection solar air heater with different fins shape. Renew. Energy 2018 , 117 , 488–500. [ Google Scholar ] [ CrossRef ]
• Promvonge, P.; Promthaisong, P.; Skullong, S. Numerical heat transfer in a solar air heater duct with punched delta-winglet vortex generators. Case Stud. Therm. Eng. 2021 , 26 , 101088. [ Google Scholar ] [ CrossRef ]
• Jin, D.; Quan, S.; Zuo, J.; Xu, S. Numerical investigation of heat transfer enhancement in a solar air heater roughened by multiple V-shaped ribs. Renew. Energy 2019 , 134 , 78–88. [ Google Scholar ] [ CrossRef ]
• Arunkumar, H.S.; Kumar, S.; Karanth, K.V. Analysis of a solar air heater for augmented thermohydraulic performance using helicoidal spring shaped fins—A numerical study. Renew. Energy 2020 , 160 , 297–311. [ Google Scholar ] [ CrossRef ]
• Shi, J.; Hu, J.; Schafer, S.R.; Chen, C.L. Numerical study of heat transfer enhancement of channel via vortex-induced vibration. Appl. Therm. Eng. 2014 , 70 , 838–845. [ Google Scholar ] [ CrossRef ]
• Nguyen, Y.Q.; Huynh, T.N.; Pham, M.-A.H. Modifications of heat transfer and induced flow rate of a solar chimney by an obstacle in the air channel. Int. J. Adv. Sci. Eng. Inf. Technol. 2021 , 11 , 482–488. [ Google Scholar ] [ CrossRef ]
• Gandjalikhan Nassab, S.A.; Sheikhnejad, Y.; Foruzan Nia, M. Novel design of natural solar air heat for higher thermal performance. Therm. Sci. Eng. Prog. 2022 , 33 , 101385. [ Google Scholar ] [ CrossRef ]
• Sheikhnejad, Y.; Gandjalikhan Nassab, S.A. Enhancement of solar chimney performance by passive vortex generator. Renew. Energy 2021 , 169 , 437–450. [ Google Scholar ] [ CrossRef ]
• Monghasemi, N.; Vadiee, A. A review of solar chimney integrated systems for space heating and cooling application. Renew. Sustain. Energy Rev. 2018 , 81 , 2714–2730. [ Google Scholar ] [ CrossRef ]
• Maghrabie, H.M.; Abdelkareem, M.A.; Elsaid, K.; Sayed, E.T.; Radwan, A.; Rezk, H.; Wilberforce, T.; Abo-Khalil, A.G.; Olabi, A.G. A review of solar chimney for natural ventilation of residential and non-residential building. Sustain. Energy Technol. Assess. 2022 , 52 , 102082. [ Google Scholar ] [ CrossRef ]
• Miyazaki, T.; Akisawa, A.; Kashiwagi, T. The effects of solar chimneys on thermal load mitigation of office buildings under the Japanese climate. Renew. Energy 2006 , 31 , 987–1010. [ Google Scholar ] [ CrossRef ]
• Chugloo, S.; Limmeechokchai, B. Application of passive cooling system in the hot and humid climate: The case study of solar chimney and wetted roof in Thailand. Build. Environ. 2007 , 42 , 3341–3351. [ Google Scholar ] [ CrossRef ]
• Abdallah, A.S.H.; Hiroshi, Y.; Goto, T.; Enteria, N.; Radwan, M.M.; Eid, M.A. Parametric investigation of solar chimney with new cooling tower integrated in a single room for New Assiut city, Egypt climate. Int. J. Energy Environ. Eng. 2014 , 5 , 1–9. [ Google Scholar ] [ CrossRef ] [ Green Version ]
• Sudpraset, S.; Chinsorranant, C.; Rattanedecho, P. Numerical study of vertical chimneys with moist air in a hot and humid climate. Int. J. Heat Mass Transf. 2016 , 102 , 645–656. [ Google Scholar ] [ CrossRef ]
• Yusoff, W.F.M.; Salleh, E.; Adam, N.M.; Sapian, A.R.; Sulaiman, M.Y. Enhancement of stack ventilation in hot and humid climate using a combination of roof solar collector and vertical stack. Build. Environ. 2010 , 45 , 2296–2308. [ Google Scholar ] [ CrossRef ]
• Zhu, N.; Li, S.; Hu, P.; Lei, F.; Deng, R. Numerical investigations on performance of phase change material Trombe wall in building. Energy 2019 , 187 , 116057. [ Google Scholar ] [ CrossRef ]

Share and Cite

Zamora, B. A Review on Solar Chimneys: From Natural Convection Fundamentals to Thermohydraulic Best-Performance Proposals. Processes 2023 , 11 , 386. https://doi.org/10.3390/pr11020386

Zamora B. A Review on Solar Chimneys: From Natural Convection Fundamentals to Thermohydraulic Best-Performance Proposals. Processes . 2023; 11(2):386. https://doi.org/10.3390/pr11020386

Zamora, Blas. 2023. "A Review on Solar Chimneys: From Natural Convection Fundamentals to Thermohydraulic Best-Performance Proposals" Processes 11, no. 2: 386. https://doi.org/10.3390/pr11020386

Article Metrics

Article access statistics, further information, mdpi initiatives, follow mdpi.

Subscribe to receive issue release notifications and newsletters from MDPI journals

Economic Analysis of Solar Chimney: Literature Review

• First Online: 29 May 2021

Cite this chapter

• Rezwan us Saleheen 3 ,
• Md. Mizanur Rahman 3 ,
• Mohammad Mashud 4 &
• Sajib Paul 3  

341 Accesses

Power generation utilizing solar chimney (SC) appears to be a radical perspective for both residential and industrial applications. Such proposition includes safeguard of mother nature reducing the ecological combustion of fossil fuels. Solar chimney (SC) initiates an opportunity in the convenience of local and isolated communities for the augmentation of industrial efforts and hence expands a probability in economic growth sustaining ecological balance. Nowadays, large-scale solar chimneys can be manufactured without any technical problems and at defined costs. Moreover, the accommodation requirements of rapidly growing population lead to the vertical growth of the buildings. The significance of electrical utilities intensifying for the necessity of proper ventilation and daylighting in place of nourish natural air ventilation system. Solar chimney also devised a driveway for natural ventilation structure for high-rise buildings. This chapter imparts a brief outline of research and development of SC power technology in the past century along with an economic analysis and cost effectiveness of solar chimney power plant (SCPP).

This is a preview of subscription content, log in via an institution to check access.

Access this chapter

Subscribe and save.

• Get 10 units per month
• Download Article/Chapter or eBook
• 1 Unit = 1 Article or 1 Chapter
• Cancel anytime
• Available as PDF
• Read on any device
• Instant download
• Own it forever
• Available as EPUB and PDF
• Compact, lightweight edition
• Dispatched in 3 to 5 business days
• Free shipping worldwide - see info
• Durable hardcover edition

Tax calculation will be finalised at checkout

Purchases are for personal use only

Institutional subscriptions

Similar content being viewed by others

A critical review on solar chimney power plant technology: influence of environment and geometrical parameters, barriers for commercialization, opportunities, and carbon emission mitigation

Techno-Economic and Environmental Implications of Electricity Generation from Solar Updraft Chimney Power Plant in Meekatharra in Western Australia

Solar Chimneys: Technology and Their Role for Transition to 100% Renewable Energy

Bernardes, M. A. D. S. (2004). Ph.D. dissertation, Universitat Stuttgart, Germany.

Google Scholar  

Billinton, R. (2005). Evaluation of different operating strategies in small stand-alone power Systems. IEEE Transactions on Energy Conversion, 20 (3), 654–660.

Article   Google Scholar  

Bonnelle, D. (2008). Private communication.

Bilgen, E., & Rheault, J. (2005). Solar Energy, 79 (5), 449.

Cabanyes, I. (1903) Las chimeneassolares (Solar chimneys). La ernergiaeléctrica.

Cao, F., Zhao, L., & Guo, L. J. (2011a). Energy Conversation Management, 52 (6), 2360.

Cao, F., Zhao, L., & Guo, L. (2011b). Simulation of a sloped solar chimney power plant in Lanzhou, China. Energy Conversion and Management 2360–2366.

Cao, F., Li, H., Zhao, L., & Guo, L. (2013). Economic analysis of solar chimney power plants in Northwest China. Journal of Renewable and Sustainable Energy, 5 (2), 021406.

Chikere, A. O., Al-Kayiem, H. H., & Karim, Z. A. A. (2011). Review on the enhancement techniques and introduction of an alternate enhancement technique of solar chimney power plant. Journal of Applied Sciences., 11, 1877–1884.

Cloete, R. (2008). Solar tower sheds light on little-used technology. Engineering News Online. https://www.engineeringnewscoza/article.php .

Dhahri, A., & Omri, A. (2013). A review of solar chimney power generation technology. International Journal of Engineering and Advanced Technology (IJEAT) .

Fluri, T., & Vonbackstrom, T. (2008). Solar Energy, 82 (11), 999.

EnviroMission Limited-Technology (2006). Technology Overview. https://www.enviromission.com.au .

Fluri, T., Pretorius, J., Dyk, C., Backstrom, T., Kroger, D., & Zijl, G. (2009). Solar Energy, 83 (3), 246.

Greentower. https://www.greentower.net .

Haaf, W., Friedrich, K., Mayr, G., & Schlaich, J. (1983a). Solar chimneys part I: Principle and construction of the pilot plant in Manzanares. International Journal of Solar Energy., 2, 3–20.

Haaf, W., Friedrich, K., Mayr, G., & Schlaich, J. (1983b). International Journal of Solar Energy, 2, 3.

Haaf, W. (1984). International Journal of Solar Energy, 2, 141.

Hong, C. S., & Lee, E. B. (2018). Power plant economic analysis: maximizing lifecycle profitability by simulating preliminary design solutions of steam-cycle conditions. Energies, 11 (9), 2245.

Hamdan, M. O. (2011). Analysis of a solar chimney power plant in the Arabian Gulf region, United Arab Emirates. Renewable Energy 2593–2598.

Jiakuan, Y., Jin, L., & Po, X. (2003). A novel technology of solar chimney for power generation. ACTA Energiae Solaris Sinica., 24, 570–573.

Kasaeian, A. B., Molana, S., & Rahmani, K. et al. (2017). A review on solar chimney systems. Renewable and Sustainable Energy Reviews, 67 , 954–987. ISSN 1364-0321.

Ley, W. (1954). Engineer’s dream . Viking Press.

Mohammed, H., Alktranee, R., Yaseen, D. T. (2019). Evaluating the performance of solar chimney power plant. International Journal of Contemporary Research and Review, 10 (6)

Muselli, M. N. G. L. A., Notton, G., & Louche, A. (1999). Design of hybrid-photovoltaic power generator, with optimization of energy management. Solar Energy, 65 (3), 143–157.

Nizetic, S., Ninic, N., & Klarin, B. (2008). Analysis and feasibility of implementing solar chimney power plants in the Mediterranean region. Energy, 33, 1680–1690.

Olusola Olorunfemi, B. (2014). A review of solar chimney technology: Its’ application to desert prone villages/regions in Northern Nigeria. International Journal of Scientific & Engineering Research, 5, 1210–1216.

Papageorgiou, C. D. (2004a). Proceedings of ISES Asia-Pacific solar energy conference , Gwangju, Korea, 17–20 October, pp. 763–772.

Papageorgiou, C. (2004b). Efficiency of solar air turbine power stations with floating solar chimneys. In IASTED proceedings of power and energy systems conference Florida , pp. 127–134.

Papageorgiou, C. D. (2007). Floating solar chimney versus concrete solar chimney power plants, Athens. IEEE, 2007, 761–765.

Papageorgiou, C. (2009). Floating solar chimney. E.U. Patent 1618302.

Papageorgiou, C. D. (2010). Floating Solar Chimney Technology.

Pretorius, J. P. (2007). Ph.D. dissertation, University of Stellenbosch, South Africa.

Sagasta, F.M. (2003). Torre solar de 750 metros de alturaen Ciudad Real (España). ed2003.

Schlaich, J. (1995). The solar chimney: Electricity from the sun . Stutgart: Axel Mengers Edition.

Schlaich, J. (1996). The solar chimney: electricity from the sun. Stuttgart, Germany: A. Menges (1995).

Schlaich, J., Bergermann, R., Schiel, W., & Weinrebe, G. (2004). Sustainable electricity generation with solar updraft towers. Structural Engineering International .

Schlaich J. et al. (2005). Design of commercial solar updraft tower systems-utilization of solar induced convective flows for power generation. Journal of Solar Energy Engineering, 127 , 117–124R.

Solar Energy. ISBN 978-953-307-052-0

US Energy Information Administration (2006).

Vlachos, N.A., Karapantsios, T.D., Balouktsis, A.I., & Chassapis, D. (2002). Design and testing of a new solar tray dryer. Drying Technology, 20 , 1243–71.

Yang, H., Wei, Z., & Chengzhi, L. (2009). Optimal design and techno-economic analysis of a hybrid solar–wind power generation system. Applied Energy, 86 (2), 163–169.

Zhou, X. P., Yang, J. (2009). Heat Transfer Engineering, 30 (5), 400.

Zhou, X. P., Yang, J. K., Wang, F., & Xiao, B. (2009a). Renewable Sustainable Energy Reviews, 13 (4), 736.

Zhou, X. P., Yang, J. K., Wang, J. B., & Xiao, B. (2009b). Energy Conversion and Management, 50 (3), 84.

Zhou, X., Wang, F., & Ochieng, R. M. (2010). A review of solar chimney power technology. Renewable and Sustainable Energy Reviews, 14, 2315–2338.

Zhou, X., & Yang, J. (2012). A novel solar thermal power plant with floating chimney stiffened onto a mountainside and potential of the power generation in China’s Deserts Wuhan , China, pp. 400–407.

Zhai, X. Q., Song, Z. P., & Wang, R. Z. (2011). A review for the applications of solar chimneys in buildings. Renewable and Sustainable Energy Reviews, 15 (8), 3757–3767.

Download references

Author information

Authors and affiliations.

Department of Mechatronics Engineering, Faculty of Engineering, World University of Bangladesh, Uttara, Dhaka, Bangladesh

Rezwan us Saleheen, Md. Mizanur Rahman & Sajib Paul

Department of Mechanical Engineering, Khulna University of Engineering and Technology (KUET), Khulna, Bangladesh

Mohammad Mashud

You can also search for this author in PubMed   Google Scholar

Corresponding author

Correspondence to Rezwan us Saleheen .

Editor information

Editors and affiliations.

Department of Mechatronics Engineering, World University of Bangladesh, Dhaka, Bangladesh

Md. Mizanur Rahman

University Malaysia Sabah, Kota kinabalu, Malaysia

Chi-Ming Chu

Rights and permissions

Reprints and permissions

Copyright information

© 2021 Springer Nature Singapore Pte Ltd.

About this chapter

Saleheen, R.u., Rahman, M.M., Mashud, M., Paul, S. (2021). Economic Analysis of Solar Chimney: Literature Review. In: Rahman, M.M., Chu, CM. (eds) Cold Inflow-Free Solar Chimney. Springer, Singapore. https://doi.org/10.1007/978-981-33-6831-6_10

Download citation

DOI : https://doi.org/10.1007/978-981-33-6831-6_10

Published : 29 May 2021

Publisher Name : Springer, Singapore

Print ISBN : 978-981-33-6830-9

Online ISBN : 978-981-33-6831-6

eBook Packages : Energy Energy (R0)

Share this chapter

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

• Publish with us

Policies and ethics

• Find a journal
• Track your research

Academia.edu no longer supports Internet Explorer.

To browse Academia.edu and the wider internet faster and more securely, please take a few seconds to  upgrade your browser .

Enter the email address you signed up with and we'll email you a reset link.

• We're Hiring!
• Help Center

Solar Chimney Power Plant-A Review

Solar technology is the novel technology which uses the natural sunlight to produce electricity. It uses the combination of three simple technologies that is turbine, vertical chimney of some longer height and glass roof collector for absorbing the sun radiations. By proper utilization of this technology the electricity can be generated in abidance and continuously for twenty four hours throughout the year in county like India where there is sunlight almost for nine months in the major part of the country. Much advancement has taken place in this technology for last three decades but the full utilization of this technology has not taken place because of various aspects. This paper presents the critical review of this important technology in the form of the advancements and developments taken place in various parts of the world and analyzes its important aspects.

Related Papers

ijifr journal

Today, in the 21st century, though we are leading a technologically advanced life, we are still facing the enormous problem of Energy crisis. The threat of depleting the all resources of fossil fuels is impending upon the whole world. Therefore it is very important for us to search for the alternative sources of energy. We already know such sources as 'Renewable Energies' which include Solar, wind, ocean thermal, Geothermal, tidal etc. forms of energy. We must emphasize on the development of technology which will harness the potential of Renewable energies and thereby reduce the consumption of valuable fossil fuels, which could then be used in case of emergency. One of such innovative technology which uses solar energy for Power Generation is introduced here. It is called as 'Solar Updraft Tower power plant'. This works on very fundamental principle of physics. It is by law of nature that, whenever fluid becomes hot, its density decreases and thereby it is pushed up by the cold and denser fluid surrounding it. Thus, the density difference which becomes the motive force causes the convection flows. In 'Solar Updraft Tower', Air is first heated by Solar collectors which cause the density difference between hot air and outside cold air. Cold air rushing in from outside sets the air flow through the vertical tower:: Analysis Of Power Generation: An Innovative Technology Of Solar Chimney (stack/ chimney). This air is made to pass across the air turbine, which will drive the generator to produce electricity. Thermal analysis of major components of the solar power plant is explained using basic Governing equations. The Prototype of such power plant (50kWe capacity) which is set up at Manzanares, Spain on experimental basis is also introduced.

Renewable and Sustainable Energy Reviews

Reccab Manyala

Solar Chimney: A Sustainable Power Generation Technology

Ahmad Alasadi

According to the Saudi vision 2030, numerous new settlements with residential housing areas will be set up in the hot-arid areas. The use of the high-temperature air in these areas for electricity generation to the residential houses is quite essential while providing urban buildings with a suitable level of infrastructure and facilities is a significant step to success in the re-urbanization project. Solar chimney power plant (SCPP) is considered to be one of the promising power generation facilities which use solar energy to generate electricity. It is a solar thermal power plant utilizing a combination of a solar air collector and a central updraft tube to generate a solar-induced convective flow, which drives pressure staged turbines to generate electricity. This paper presents a description of the functional principle of the SCPP components, and some results from designing a medium scale unit using a simple mathematical model are given.

Global Journal of Research In Engineering

Md Takmil Sakir

IRA-International Journal of Technology & Engineering

Dr. Premendra J A N A R D A N Bansod , N. Wankhade

Conventional energy sources like coal and oil used for power generation causes various environmental problems like creating pollution and creating ecological imbalance. These sources are also depleting due to lesser use of alternative resources. Chimney operated solar power plant is one of the best alternative which can be used to produce power in large capacity with the use of solar energy. It consist of very few number of parts like turbine, collector and chimney. This paper consist of study of effect of different process parameters on the performance this chimney operated solar power plant. A small prototype model of this power plant is fabricated which has collector of 1.8 m diameter and chimney of maximum height of 2.0 m. D.C motor with small generator and blades is used as turbine to get power output. The various process parameters like temperature, pressure, velocity are used to determine power output and efficiency of power plant. Numerous mathematical correlations were used to correlate these input and output parameters. The effect of chimney height on these parameters was studied. It was determined that temperature and velocity are the important parameters which improves the performance of solar chimney power plant along with chimney height and collector diameter.

IJIRT Journal

In this study, a parametric 3D computational fluid dynamics (CFD) analysis of SCPP was performed to observe the effects of chimney height, collector slope and chimney diverging angle on performance of Manzanares prototype. Numerical models were incorporated with solar load, DO (discrete ordinates) and RNG k-ɛ turbulence models. Firstly, CFD results were validated by comparing them with Hassan et.al [2017]. Several numerical simulations were performed on varying height of chimney, collector's slope and chimney diverging angles to improve the performance of solar chimney. Numerical simulations were performed at height of chimney H=180m-210m, chimney diverging angle = 2 0 , 4 0 , 6 0 and at collector slope = 2 0 , 4 0 , 6 0 , 8 0 and 10 0 being all other parameters constant. It is seen that both velocity and temperature increases with increasing collector's slope due to enhanced heat transfer and mass flow rate. Higher collector slopes deteriorate the smooth air flow by developing vortices and recirculation of air, which obstructs the air flow and may reduce the overall performance. At height of 190m at 00 divergent angle 37.0840kW power is received whereas at 190m and 20 divergent angle 71.5204kW power is received with collector slope 40; therefore, this parameter of solar chimney power plant is best. Index terms-Solar chimney power plant; computational fluid dynamics; chimney height, solar collector slope; chimney divergent angle I.INTRODUCTION Solar radiation received by sun is vast and can be converted into thermal energy as well as electrical energy. The primary component that initiates the conversion process is a solar collector. A solar collector is either flat or concentrating type based upon the end use of energy or temperature requirement. Thus a solar collector is a device which converts incident solar radiation into thermal energy via a heat transfer fluid (water or air). The heat obtained by solar collectors can fulfill energy demand directly or it may be stored. Performance enhancement of solar collector can encourage its use for power saving in low temperature heating applications. Instantaneous useful energy found by the collector is result of an energy balance on the solar collector components. To evaluate the amount of energy produced in a solar collector properly, it is necessary to consider the physical properties of the materials. Solar radiation, mostly short wavelength, passes through a transparent cover and strikes the energy receiver. Low iron glass has high transmissivity. Hence, it is commonly used as a glazing cover which also greatly reduces heat losses. Natural convection solar chimney power plant mainly depends on heat flux available on absorber plate, from where air gain the energy and due to bouncy effect, it starts moving in the upward direction. In natural convection solar chimney power plant, heat transfer mainly due to convection whereas heat transfer through radiation is avoided. With the used of chimney effect natural convection solar chimney power plant performance get increase. This work performs the effect of different chimney height on the performance of solar chimney power plant and optimize the boundary condition 0n the solar chimney power plant. It also analyzed the effect of different angle (like-chimney divergent angle and solar collector angle) on the performance of solar chimney power plant. Effect the heat flux at different geometric conditions was also analyzed.

Sustainability

This research presents a comprehensive review of solar chimney power plants (SCPP) as a reliable source of renewable electricity generation. Solar chimney power plants differ from other renewable energy technologies because thermal and momentum effects result in 24-h electricity generation. However, they are influenced by a wide range of design, geometrical and operational parameters, and environmental conditions. This review evaluates the design aspects and the theoretical, numerical, experimental, and performance findings in previous works holistically and concisely. The study also extensively discusses the various optimization strategies, advantages, disadvantages, and limitations of solar chimney power plants. Energy storage aspects and hybrid system designs are also addressed in the present review in order to overcome the known handicaps and limitations of solar chimney power plants. The performance figures of the technology are clearly demonstrated as a function of the design ...

International Journal of Contemporary Research and Review

Mohammed Alktranee

Growing global energy demand has become worrying due to the fluctuating fossil fuel prices, the damage caused by the use of conventional fuels as the toxic emissions and global warming. Therefore, dependence on alternative and sustainable sources has become a pressing topic. In this paper will review the performance of solar chimney power plant, the parameters that affect on the performance, conversion efficiency and power output for a different collection of prototypes. During this study there are found that power output of the solar chimney power plant is directly proportional to increase of the height of the chimney, specifically when the solar chimney is sloped where the performances is better as well as the conversion efficiency. While increasing the diameter of collector will provide a big heating area which cause a decrease of air density due to rise in the air temperature under the solar collector which lead to increase the flow of driving force and the mass flow rate that c...

Robera Daba

Loading Preview

Sorry, preview is currently unavailable. You can download the paper by clicking the button above.

RELATED PAPERS

IAEME Publication

IOSR Journals

محمد حميد خلف

Lecture Notes of the Institute for Computer Sciences, Social Informatics and Telecommunications Engineering

Solomon Teferi

Hosam Nasef

Garba Ngala

Recep Tayyip Erdoğan Üniversitesi Fen ve Mühendislik Bilimleri dergisi

Vinayak Singh

Renewable Energy

Mohammad O. Hamdan

Amir Kasaeian

Muhammad Tawalbeh , Asma Khasawneh

Heat and Mass Transfer

Hossein Mansouri

2012 International Conference on Renewable Energies for Developing Countries (REDEC)

Adel Mourtada

International Journal of Advanced Engineering Research and Science

Aravind James

•   We're Hiring!
•   Help Center
• Find new research papers in:
• Health Sciences
• Earth Sciences
• Cognitive Science
• Mathematics
• Computer Science
• Academia ©2024